Skip to main content

Posts

Found the parasitic draw... it was the bottom left RAD CIG fuse which had a 25 amp fuse in it... dropped reading from .09 to .01 ... since I don't use the radio or cigarette lighter I left the fuse out...
Your next clutch: 16952 - EXEDY Racing Stage 2 Cerametallic Clutch Kit / Thin disk
Battery voltage holds strong without trickle charger... So battery is GOOD...I wasn't able to disconnect the alarm system to see how much if any it effects the 110 mA draw... I did make an appointment on Monday to have the alarm removed... The car still has a hard starting issue but that's a whole other issue to deal with down the road :) I just want to get my resting battery draw bellow 50 mA first...
Monday May 15th 8:34 AM.... Disconnected the positive lead to the battery and disconnected the battery trickle charger... If on Friday I connect the battery and the car starts up normal then I know the battery is GOOD If on Friday I connect the battery and the car doesn't start the the battery is BAD If the battery is GOOD, then there is a parasitic drain from the car... If the battery is BAD, then buy another battery ... A reading of 12.65-12.77 volts means your battery has a full charge. 12.45-12.54 volts means you have a 75% charge, 12.24-12.29 is 50% charged, and 11.99-12.06 volts is 25% charged. 11.75-11.89 volts means your battery is dead. 5/15 10AM  volt reading 12.84 Also checked for parasitic draw on the car... meter settings bellow... one meter terminal to the positive terminal on the battery... other meter terminal to the positive cable going to the battery... reading was 0.10 .... I have a 110 MA draw on the car... should not be higher then 50 MA accord...
Brake Caliper Rebuild kit info: We have confirmation! *ALL* MkI use the brake caliper rebuild kit, regardless of year - so long as you haven't swapped on some other calipers (looking at you here, Marc) - and they are still available new from Toyota. One kit does both calipers on that end of the car; to rebuild all four calipers you'll need one front kit and one rear kit. These kits include piston seals and boots, circlips, caliper slide boots, assembly grease, and on the rear, seals and o-rings for the parking brake mechanism as well. Last time I got a parts store "rebuild kit" I think it was a piston seal and a boot. 04479-17011 - $30.62 - Rebuild kit, rear caliper 04479-32011 - $21.52 - Rebuild kit, front caliper As always, give me a call if you need 'em! I'll be here all day today, 7:30 AM to 6:00 PM Pacific. If this is grumpier than normal, let's blame it on the early hour and lack of coffee intake... Aaron Willis, Parts Dept. - ...
Doug came over and showed me how to change break pads... changing rotors would be very simple as we'll... and maybe next time replace my Calipers...
AW11 registered in the US 2005 Total count: NA = 20,764 SC = 1,752 1985 = 3,332 1986 = 7,198 1987 = 5,475 1988 NA = 2,506 1988 SC = 1,156 1989 NA = 2,253 1989 SC = 596 California: 1985 = 472 1986 = 2,016 1987 = 1,300 1988 NA = 490 1988 SC = 296 1989 NA = 408 1989 SC = 153
Changed the Oil and filter today... Also replaced the Transmission fluid with RedLine MT-90 full synthetic fluid... added a little arch oil AR9100 Friction Modifier to the tranny... it took just under 4 quarts to top off...
Best lap Streets CW 135.68 shocks set at 1/8 from soft and tire pressure 29-30 lbs hot One thing I noticed is less spots the car went over 1G, in fact turn 8 only but lap times were lower...
Autocross today... 1/2 turn from soft seems pretty good... might try 1/4 next weekend at Streets...
The good: New springs have been installed, and new more aggressive camber settings The Bad: Stiffer springs negated lowering the car... I'm same height as before The Ugly: Cost me $650 Solution: Need 6" 200lb front springs, and then put back 7" 250lb rear New adjusted estimated car weight with full tank: 2268 lbs
Springs arrived :)
Really learned something today... adjustments to the suspension aren't really noticeable until you take the car to the limit... I had my Koni yellow set at 1.5 turns from soft... my car was OK on the track but then I decided to try 2 turns from soft... harder... car became a little harder to handle, even under breaking... so I then went to 1 turn from soft and the whole suspension came alive... It was better under cornering, braking and especially predictable in a power slide... way more fun to drive... Next track day I will play with tire pressure and might even bring a temp gauge... Best lap of the day was 1:36.45 , clock wise Red zone is over 1g... maximum 1.2g
TO DO LIST Fix speedometer and replace gauge cluster to kmph Check engine compression fix turning signal Remove Alarm system completely ? Get 6”  2.5” 300lb front / 7” 2.5” 350lb rear springs from Ground Control Re align car with new springs, 1/2” lower and more front Camber Improve exhaust ( stainless steel custom ) — weight reduction Replace side and rear windows with Lexan  — weight reduction Possibly remove power windows with a strap up / down system — weight reduction Next three items done at same time-ish ( Talk to shop before doing anything to engine ) 1) Larger pulley to increase compression 2) New CPU 3) Re Map engine  Replace all hoses re paint engine covers remove the rest of engine bay insulation 
apparently this was the problem with my broken speedometer... connects the speedometer cable to the plastic gear at the transmission end... $14... I picked up the part from Ricks Japanese and didn't schedule an appointment... he never apologized for miss diagnosing the car ... what a dick... so now I'm going to try this guy called Ray who lives in Van Nuys... Recommended by C&A Auto Service who was recommended by this asian guy at TQ :)
So seems like my speedometer troubles were not related to the gauge cluster but a $14 gear that connects the speedometer cable to the transmission... This after I ordered a gauge cluster from Malaysia and then returned it to the guy claiming that its broken... I then ordered another one from Canada... Don didn't seem apologetic at all, WTF ? I specifically remember asking him if he connected the speedometer to the gauge with a drill and he said he tested it and its broken... Rick the owner told me himself that it was broken at the back of the speedometer gauge... ???? I've decided to no longer go there... They are obviously not only incompitent but also lie... sad because I was so hopeful I found a good mechanic...  They didn't even thank me for the box of donuts I brought them... I had to ask Don if he liked the donuts and he then said "yes. thanks" Oh well... time to find a new mechanic...  A guy at the RC track recommend this place kinda close to me... https:...
suggested setup in a MR2 forum Camber Front: -2 degrees Camber Rear : -1 1/2 degrees Caster : +6 degrees Toe in front: 1/16 in. ( 1/8 in. out for auto cross) Toe in rear : 1/8 in. ( 1/16 in. out for auto cross) Front:  Caster 5 Camber -2.7 Toe right between 1/8 and 1/16 out Rear: camber -2.5 Toe 1/16 in
Crappy news... Looks like the gauge cluster from Japan is broken... The guy is totally willing too return it and pay for shipping but really feels like it should be working... my mechanic insists it doesn't work... anyways... I found another Kmh cluster in Canada... and ordered a new cluster cover from Neil in Wails... They put my gauge back in the car and I'm picking up later today... I might try new mechanic next time... Don always seems like he super busy and he makes me feel like I'm intruding on his regular work flow... ???
Bought 40 lbs of dry ice and removed the sound deadning ... what a pain in the ass even with the dry ice... removed 14.2 lbs of deadening... Need to let it dry completely and then paint next sunny day... Estimated car weight 2,281 with full tank of gas...